1-800-334-1001

 

Email Us Credit App Repair Form

Menu

TILT-TO-LOAD DRUM TUMBLERS

Morse Tilt-To-Load Drum Rotators have power-lift, and tumble drum "corner-over-corner" to thoroughly mix contents. The drum tumbler holds your drum on an angle to rotate drum  with vigorous "corner-over-corner" action!

Tilt-To-Load Drum Tumblers rotate a plastic, steel or fiber drum.

Mix a 55-gallon drum or a 30-gallon drum.

 

Tilt-to-Load Drum Tumblers Brochure

 



drum tumbler

drum tumbler

image

Load upright drum at floor level.back

Easy to Load by hand truck or hoist without the hazards of manual drum handling.

Quickly load an upright drum into the Tilt-To-Load Rotator at floor level with Drum Truck.

image

Load upright drum at floor level.back

Easy to load a drum with your hoist to avoid the hazards of manual drum handling.

Quickly load an upright drum into the Tilt-To-Load Rotator at floor level with model 81 Drum Spotter or with a below-hook drum lifter and your hoist or crane.

image

 

Secure your drum in drum rotator using the cinch chain around drum and two top clamps.

 

image

Tumble Many Different Drums, including 55-gallon and 30-gallon drum sizes

Drum Holder on Tilt-To-Load Drum Tumblers supports your drum with base plate under the drum,
two clamps on top of the drum, and cinch chain around drum.

 

 

 

 

 

 

  • Tumble drum 29" to 37" (74 to 94 cm) tall
  • Tumble drum 18" to 23.5" (46 to 60 cm) in diameter
  • Variable speed: 5 to 20 RPM
  • Motor is 2 HP, 60 Hz.
  • Capacity:
    • 800 Lb. (363 kg) full drum
    • 400 Lb. (181 kg) half-full drum

image

Tumble 30-gallon drum with Tilt-To-Load Drum Tumbler

Use ergonomic power tilt control to raise drum to rotate position.

Then use second control to start and stop drum tumbling.

Turn motor on to activate drum tumbler hydraulics. Tilt drum to top position with RAISE control valve. Begin drum rotation with the ROTATE control valve.


Use ergonomic power tilt control to raise drum to rotate position. Control Mast can be positioned away from Tilt-To-Load Drum Tumbler to be outside a safety enclosure.

Control mast can be positioned on either left or right side (shown above) or at back of Tilt-To-Load Drum Tumbler.



OPTIONS

image

Oil Cooler Kit for AC Powered Tilt-To-Load Drum Tumblers for applications requiring a higher service factor, such as longer run times or operating in areas with high ambient temperature

 

 

 

 

 

 

 

 

Oil Cooler factory installed on AC Powered Tilt-To-Load Drum Tumbler

Option # 5014i-P

 

Kit for field installation of Oil Cooler on your AC Powered Tilt-To-Load Drum Tumbler

Kit # 5014KIT-P


image

Safety Enclosures to Meet OSHA Requirements

Morse enclosures with safety interlock are available as a way to meet OSHA requirements. Drum Tumbler and Control Package sold separately.

Enclosure outside post-to-post dimensions:
L88" x W52" x H63.25" (224 x 132 x 161 cm)


Install all Morse Rotators in accordance with local requirements for enclosure and safety interlock, etc. One way to accomplish this is with a Morse enclosure with safety interlock, so the rotator automatically turns off when enclosure door is opened. Power connections and motor controls must also comply with applicable local codes.

 

For OSHA compliance in the USA, see OSHA subpart O.1910.212(a)(4) "Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place."

Do you have a question or need application assistance?